Samurai Express^™

The Samurai Express™ is a high-performance colocation and entry-level core router that provides wire-speed performance with leased telco and ethernet connections at speeds up to one gigabit. The system hardware is a 2U 19-inch rackmount chassis with locking access door, removable processor card, high-performance memory, flash storage, PCI Express backplane, and onboard dual 10/100/1000 ethernet ports.

The Samurai Express provides two PCI and two PCI Express slots for expansion. The system is also available as the PCI-only Samurai which provides four PCI expansion slots. The PCI and PCI Express slots accept ImageStream LAN, WAN and voice interface cards that support a wide range of network applications. With these add-on cards, the Samurai Express can connect IP data networks using T1/E1, DS3/E3, OC3/STM1, OC12/STM4, 10 Mb to 10 Gb ethernet, basic rate ISDN (BRI), and 56 K dial-up circuits. Voice cards include support for analog FXO/FXS, basic rate ISDN (BRI), and T1/E1 Primary Rate ISDN (PRI).

Samurai Express™ Router

Downloads

Data Sheet

Replacement Guide
Cisco 1013
Cisco 3945
Cisco 7206
Juniper M5

The Samurai Express takes advantage of the ImageStream Linux™ router distribution, which provides support for NAT firewall security, IPsec and SSL virtual private networks (VPNs), quality of service (QoS), VLAN tagging, VoIP Gateway, SoftPBX, Lawful Intercept (including CALEA), VRRP for LAN failover, dynamic routing, packet filtering, bridging, peer-to-peer traffic control, Azotel SIMPLer OSS support and more. ImageStream Linux also includes the Inetics™ platform, which provides a tightly integrated Linux kernel, management software, and the Inetics Driver Component Architecture (IDCA). IDCA supports WAN protocols including PPP, Cisco HDLC, frame relay, ATM, and SoftCell™ ATM. Inetics also makes it easy to troubleshoot LAN and WAN connections by providing real-time port status and performance monitoring.

The Samurai Express router can be used in a wide range of applications from the core to the edge. It is ideal for high-performance network applications that require wire-speed performance with redundant power. The Samurai Express works in most applications where the Cisco 1013, 3945 and 7206 routers are deployed, and it is commonly used in multihomed networks that require high-speed ethernet or SONET/SDH connectivity. The Samurai Express is ideal for service provider and telco core and edge applications, enterprise core and Internet gateway applications, and other networks where a high level of performance, scalability, and redundancy is required.

Hardware

Chassis: Steel 2U 19" rackmount
CPU: Intel Dual Core
Memory: 1 GB
Storage: Fixed flash disk
Network Ports: Dual 10/100/1000 ethernet
Management Port: Serial console
SE1000 Expansion Interface
(1) x16 PCI Express Slots
(1) x4 PCI Express Slots
(2) PCI slots
SR1000 Expansion Interface
(4) PCI slots
Power Supply
Design: Switch-selectable voltage
AC Mains Voltage:
85 to 132 VAC @ 115 V setting
185 to 243 VAC @ 230 V setting
AC Mains Frequency: 47 to 63 Hz
Power Output: 350 W
Dimensions
Height: 3.5 inches (8.9 cm)
Width: 19 inches (48.3 cm)
Depth: 17.4 inches (44.2 cm)
Weight: 21.4 lbs. (9.7 kg)

Options

LAN Cards
1, 2, 4 and 6 port GigE UTP, optical or SFP
WAN Cards
1 port OC12/STM4
1 or 4 port OC3/STM1
1 and 2 port DS3/E3
1 port channelized DS3
1, 2, 4 and 8 port T1 or E1
1, 2, 4 and 8 port sync serial
1 port basic rate ISDN (BRI)
1 port 56 K modem
Voice Cards
1, 2, 4, 8, 12 and 24 port FXO/FXS
1, 2, 4 and 8 port BRI
1, 2 and 4 port T1/E1/J1 PRI
Power Supplies
-48 VDC
Dual input redundant AC or DC
Model Numbers
SE1000 - PCI and PCI Express slots
SR1000 - PCI slots only